top of page

Gas Furnace Repair, Tune-Ups & Safety Checks in Central Texas

Not heating properly? Making an unfamiliar sound or smell? We inspect, test and explain what your gas furnace needs.

When the heat comes on for the season, an unfamiliar smell, a new noise or a room that stays cold deserves an explanation. Hardison Heat, Air & Plumbing provides gas-furnace repair, seasonal tune-ups and condition checks throughout our Central Texas service area. We investigate the symptoms and explain what the equipment needs before recommended work proceeds.

24/7 service availability. We travel to your home; call to discuss scheduling.

Gas odor or a CO alarm? Act first.

If you smell gas or a carbon monoxide alarm sounds, leave the building and call 911 from outside. For a suspected gas leak, also contact your gas utility from a safe location. Do not wait for routine service or reenter until emergency responders permit it. Carbon monoxide has no smell.

Gas furnace diagnosis, maintenance and condition checks

A repair visit investigates a problem. A seasonal tune-up addresses applicable maintenance and operating checks. A condition assessment helps you understand observed wear, operation and repair needs, whether or not the furnace has stopped heating.

This service focuses on gas furnaces. Heat-pump and electric-heating service remain available through our separate heating pages.

What have you noticed at home?

A furnace that heats on one call and stops on the next needs a different investigation from one that runs steadily but leaves rooms cool. Tell us what happens before, during and after the problem. We use that history to choose relevant checks rather than assume every furnace needs the same part.

First-use odors and unfamiliar sounds

“Something smells different when the heat starts.”

Odors need to be distinguished rather than automatically called normal or dangerous. Do not keep running the furnace to see whether an unexplained odor disappears. Suspected gas leaks and CO alarms require the emergency response above.

“It bangs, rumbles, squeals or rattles.”

Ignition behavior, moving parts and airflow can produce different sounds. When a sound occurs in the cycle helps guide inspection; the sound alone is not a diagnosis.

Weak heat, shutdowns or a blower without burners

We follow the operating sequence and compare symptoms with relevant measurements instead of replacing parts by guesswork.

“It runs, but the house does not get warm.”

Weak or cool air, uneven temperatures and long run times call for evaluation of furnace operation, airflow, controls and other relevant conditions.

“It starts, then shuts off again.”

Repeated starts, short cycles and intermittent heat can have different causes. Testing helps identify where operation stops and what needs attention.

“The blower runs, but the burners do not come on.”

This is a diagnostic call involving the ignition sequence and related controls. We investigate the cause; do not bypass safety devices to force heat.

Tell us what you have already observed. Do not run or restart a concerning furnace solely to demonstrate a symptom.

What we inspect and test

Checks are selected for the equipment, accessibility and reported symptoms. Every furnace and visit does not permit or require an identical set of tests.

  • Your reported symptoms and operating history.
  • Accessible furnace components and visible condition.
  • Ignition, burners, relevant safety controls and operating sequence.
  • Blower operation, filter condition and airflow concerns.
  • Temperature rise and other applicable operating measurements.
  • Accessible venting and combustion-air conditions.
  • Gas pressure where applicable.
  • Combustion analysis using Fieldpiece equipment.
  • Carbon monoxide measurements appropriate to the concern.
  • Visual and camera-assisted checks of accessible heat-exchanger areas.

We explain the findings, the limits of the assessment and recommended next steps before proposed work proceeds.

Call for Gas Furnace Service — 254-500-4957

Request a gas-furnace service appointment

“My furnace is old. Is it still working properly?”

Age alone does not require replacement. We assess observed wear, operation, test results, repair needs and accessible components. We explain repair or further-evaluation options based on what we find, without promising remaining lifespan.

“It heats, but I want it checked before winter use.”

A seasonal tune-up is useful when you want to understand your gas furnace’s current condition before depending on it regularly. Mention changes in sound, smell, cycle length or comfort even if it still heats. Maintenance can identify concerns; it cannot guarantee future fault-free operation.

Carbon monoxide and heat-exchanger assessment

Combustion analysis measures conditions in the furnace’s combustion/exhaust stream. Indoor-air CO measurements assess the air in the locations tested. These are different measurements with different purposes. We explain them in context with burner operation, venting and other observations.

Visual and camera-assisted checks can examine accessible heat-exchanger areas. Equipment design and access may leave surfaces unseen. A camera cannot reveal every surface or rule out every defect. Combustion analysis and CO readings support an assessment; they do not independently certify the entire furnace or home as safe.

Understand the findings before deciding

We discuss what the inspection shows and the recommended work before you decide how to proceed. A repair recommendation should relate to the symptoms, observed condition and test results—not a blanket assumption that every concern needs replacement.

A photo is not a test result

The genuine Hardison furnace photo on this page shows burners and accessible equipment. Flame appearance in a photograph cannot establish correct combustion or rule out a CO concern. Measurements and inspection provide different information.

Planning gas-furnace service in Central Texas

For Central Texas service, tell us whether you need a repair, seasonal tune-up or equipment-condition check. Share the symptoms and operating history you already know. Call 254-500-4957 to discuss availability; service is provided at customers’ homes.

Clear explanations from Hardison

Hardison Heat, Air & Plumbing is the same locally owned, family-operated business serving these communities from Temple. The city pages describe our service coverage; they do not represent separate offices.

  • Diagnosis guided by the reported problem.
  • Checks appropriate to the equipment and access.
  • Findings and recommendations explained before work.
  • Inspection limits stated clearly.
  • Heat-pump and electric-heating service also available.

Gas furnace service areas

We travel to homeowners throughout our Central Texas service area.

Gas furnace questions from homeowners

Can I book a check if the furnace still heats?

Yes. A seasonal visit can assess operation, accessible components and applicable measurements before you depend on the furnace regularly. A tune-up cannot guarantee that a future failure will never occur.

Does furnace age decide whether it needs replacement?

No. Observed condition, operation, test results, repair needs and available options matter. We discuss the findings rather than treat a birthday as a diagnosis.

Do you also work on heat pumps and electric heat?

Yes. This page focuses on gas furnaces. Our separate heating-repair pages cover heat pumps and electric heating; tell us which system you have, if you know.

Call for gas furnace service in Central Texas

Describe your furnace concern to Hardison Heat, Air & Plumbing. We offer 24/7 service availability and will discuss the appropriate next step and scheduling.

Call for Gas Furnace Service — 254-500-4957

Request a gas-furnace service appointment

bottom of page